新闻资讯
current position: Home > News Center > Industry information

What should be done when using horizontal mixer

2022-01-21 16:52:28
times

Some accidents are often caused by improper use and operation of some equipment. Although two-dimensional motion mixer is not so dangerous, if some things that should be paid attention to in the process of use are not noticed, then huge accidents or harms will also occur. So how can this kind of machine avoid some accidents in the process of use? In fact, in order to avoid the occurrence of accidents, it is generally necessary to operate the machine strictly in accordance with the steps, and we should understand some of its related content. The operation content of this mixing machine is as follows:


First, the key step of the two-dimensional motion mixer Z is to add material to the barrel. If the feeding specification can make the material inside be fully mixed, if the material is added too much, it will make the machine seriously overloaded, and it is very unsafe to operate, and it is easy to throw the barrel. In fact, the method of feeding is very simple: to open the lid of the machine inlet, take out the blind cover, and then connect the suction pipe and suction pipe and clamp, according to the swing point of the switch, the general feed 80 kg can be.




Second, it is necessary to set the time of mixing a batch of material first, and then press the two buttons of rotation and swing. The material inside the cylinder will continue to swing and shake with the cylinder. After Z, the set time arrives, the machine will automatically stop rotating.


Third, open the cover of the discharging pipe, connect the material receiving pipe to the discharging port, and then press the discharging button of the two-dimensional motion mixer, so that the material inside comes out along the pipe. When the material is all put out, close the button, disconnect the power supply, and clean the machine after Z.


After using a large heavy machine, the groove part inside more or less will have a certain residue in it, in order to keep the life of the machine can be a little longer, this has to need a clear maintenance process of us! What about clinging to the groove and having difficulty removing it in other basic ways?


The first step is to check whether there is a gas injection device in the grease adding line.


The second step is to check whether the nozzle is blocked.


The third step is to check whether the screen in the filter tank is damaged.


The fourth step is to adjust the Angle of the nozzle so that the oil can not be sprayed onto the wall panels and blades at both ends of the mixer.


Fifth, of course, appropriate control of the heating temperature of oil, to prevent oil temperature is too high to spray into the material oil group.


The sixth step is to increase the finished product inspection screen after mixing in the process, and break up the mixed oil group to remove.


Of course, these need you to practice carefully, carefully to do, just like your clothing. For mixers, there are other categories of mixers. There are several kinds: small mixer, V-type mixer, THREE-DIMENSIONAL mixer and trough mixer. Just a little bit about what they do.


Small mixer:


Small mixer mixing part for shaft single blade, blade Angle on the single oar design is very appropriate, single propeller rotates, material rolling up and down, blade through the material at the same time, the mixing tank left and right sides of the pushing force of produce certain Angle, the mixing tank material can't rest in any corner, so that the material mixing. The machine adopts the sealing method of end face sealing, adjusting sealing nut and compensating axial pressure. This method has been proved to be effective by long-term practice.


3 D mixer: driven by the active shaft, the cylinder of the 3 D mixer carries out the repetitive compound movement such as translation, rotation and tumbling, so as to promote the material to move in three directions along the simplified form, so as to realize the mutual flow, diffusion, accumulation and doping of various materials. In order to achieve the purpose of uniform mixing. This machine mixing barrel multi-direction movement, the material has no centrifugal force action, no specific gravity segregation and stratification, accumulation phenomenon, each component can have a wide weight ratio, mixing rate of more than 100%, is the ideal product in all kinds of mixers.


Tags

Previous:None

Recently Viewed:

Contact us

Shanghai Huasan Powder Equipment Co., LTD

Contact person: Manager Zhu

Tel: 021-57460338/57460358/57468812

Mobile phone: 13818804871/18017628352

Fax: 021-57463615

Email:sales@huasanpowder.com

Address: No.33 puzhuang Road, Zhuanghang European Industrial Park, Fengxian District, Shanghai